Last week, when we had both received our LED light reels in the mail from Amazon.com, we set up a time to get together and get them installed. Andy had all the parts and tools we needed for the job. First we did his Lazy Daze motor home, and when his was done and he liked the way it worked, we went up to The Palms and did the same thing to my motor home.
Andy supplied the parts, tools, knowledge and labor, and I helped with ideas and, ummm, well, ideas and company.
 |
| LED Strip light, Waterproof LED Flexible Light Strip 12V at night |
 |
| It comes with the LED lights on a reel, with wires at both ends. |
Andy soldered the wires on one end of 12v plug to another length of wire he had on hand so we would have enough wire length between the 12v plug/receptacle in the dash and the LEd lights in the engine compartment. Before it reached the LEDs in the engine, the wire had to go from the inside of the cab, through the door jamb, behind the fender and out into the engine, where it was soldered to one end of the LEDs.
 |
When he had the wires soldered together, he shrunk the plastic tubing so it would stay over the soldered area, keeping everything neat and protected.
Below is Andy's butane soldering tool. The tip is used for the soldering, and the heat coming from the red-hot openings was used to shrink the tubing.
He took the dash cover off so we could thread the wire behind the cover from the right side by the 12v receptacle to the other end by the door. See the green and yellow wire?
Feeding the wire into the door jamb and through the area behind the fender.
Using a "grabbing" tool to grab hold of the wire and pull it through the fender area and out into the engine.
Once the wires were out, they had to be soldered to one end of the LED light wires. Hazel dropped by after her day of volunteering at the Visitor's Center, and found us working on this project, and she stepped up to help so I could get some photos.
 |
| Joking around - do you think Andy has been to Mardi Gras? |
Soldering the wire onto the LED light wire:
Next we draped the line of LEDs around the engine, making sure to drop some into the now empty rodent nest area (photo to follow) in front of the headlight in an empty, flat area. We were careful to keep the lights around the edge of the engine - away from any moving parts or areas where the heat would be too high. When we were happy with the way the lights were laid out, we zip tied them in place. Then Andy put shrink tubing around the other two ends of the LED wires to keep them from touching, and we were done.
Fleur and Power needed their walk, so Hazel took them around the campground with Katie keeping her company in the car. Since I was still busy with the LED project, I stayed home to keep working. (Wow, look at that shiny car.) Katie LOVES Hazel, this "play date" wasn't with Fleur and Power, it was definitely with Hazel.
So, every night when it starts getting dark, I plug the 12v plug into the dash receptacle and the lights go on. In the morning, I unplug it. I have a sticky note attached to my computer so I won't forget in the morning. The lights take up a very small amount of energy, so I don't have to worry about them draining the truck's battery. I am starting the engine every four or five days, though, just to make sure.
And this is what it looks like at night when the LEDs are lit. When the hood is closed, you can see lights coming from the engine underneath, so hopefully, that will deter the critters. If they DO get in anyway, either the bright lights or the Fresh Cab should drive them out. See the little white packets strewn about? I really only need one packet in this small space, but I didn't realize that, so I put six, all over the place. Since they are there, I will keep using them all. When they are no longer doing their job, I'll replace them with just one. (I have a sticky note by my steering wheel to remind me to remove them when I start the engine.)
 |
| Whose little ears are those, sticking up in the windshield over the hood? |
And that's how Andy, with my help and company, rigged up a reel of LED lights into a rodent deterrent in my engine (and his).
The photo below is of the area right behind the driver's side front light. There is a flat area there that's apparently perfect for a rodent's nest, because I found this in mine, a pretty big nest, and when we later checked Andy's engine area, he had a nest in the same spot. I had no idea it was there, but Hazel kept telling me I had to have a nest somewhere because of all the little mice I was finding a few months ago. I was lucky that the mice brought in all the nesting material and didn't take anything from my engine wires, etc., to build their nest. If you park your motor home where rodents are, check this area in your engine, too. You might be surprised what you find.
 |
| This photo was taken standing in front of the headlight, looking down. See all the "stuff" there? That's a rodent nest. |
I put on a face mask and latex gloves, put my arm down there and pulled the material out. (If you do find a nest, make sure you use a mask and gloves, just in case. You don't want to be exposed to the Hantavirus which is spread by infected rodents through their dried urine, saliva, and feces. I keep some of these masks on hand for smokey areas, and luckily had them available to use.)
I reached down three or four times and got most of it out, putting the material into a baggie each time. My arm went down easily, but it was hard to pull it back out. I scraped my arm and got some scratches, so as soon as I got as much as I could out, I sealed the baggie and went in and washed my arm with soap and hot water, and later put alcohol on the scratches, as suggested by Hazel and Andy.
 |
| This is the baggie full of nesting material. It went directly into a dumpster along with my mask and gloves. |
I am still putting my Fresh Cab into the engine when I'm parked and every night I've plugged in the LEDs. I'm pretty confident that I won't have any more critters in the engine. And so far, the cabin has been rodent-free, too, since Hazel and I plugged up all the holes a while ago.
It was a pretty easy mod, but without Andy's knowledge and tools and materials, I couldn't have done it. When I ordered the LEDs, I thought they would come with a 12v plug on one end. I was pretty surprised when they arrived with just wires at both ends. Thanks, Andy! I appreciate that you were so generous helping me get this done. I couldn't have done it without you.
Today we are heading southwest, toward Quartzsite. Yeaaaaaaa! We're leaving late morning, so I don't know how far we'll get, but it's getting too cold here at night, so it's time to move on.
From me and Katie in our mouse-free house, have a great Friday, everyone! :)
